Yankee Equipment Listing 2013

 

208-839-2665, 503-709-8378, michaelknapp@frontier.com

 

Debarker System

- Two (2) six (6) strand 30’x20’ decks with drives, “S” wrap with pin stops

- 50’ log haul infeed to debarker w/drive

- 43” Salem/Brunette ring debarker with drives, HPU

 

(estimated weight of debarker 50,000#)

 

- Operator cab & controls for the debarker

- 50’ log haul outfeed with kickers with drive

- 50’ log haul infeed conveyor to log Cut OFF Saw

- Log Cut Off Saw with motor & HPU

- 80’ + Log haul outfeed conveyor from cut off saw complete with


 

Four (4) sets of log kickers

- Operator cab & controls for the cut off saw

- Quincy model 850H 200HP air compressor s/n72724 (25,211hrs)

- Waste conveyors from debarker to cut off saw

- Sub steel to the ground - MORE PHOTOS and INFO UPON REQUEST

 

 

 

Debarker SystemDebarker System for Sale


 

Headrig Carriage System Left Hand consisting of:

- Four (4) Knee Klamath Iron 42” Carriage “Slant” with linear


 

Positioners, Brownsville cant turner each knee, L.H.

Model 34 CM&E 6/8knife Headrig slabber L.H. (no linear)

Positioner and 200HP drive

- 7’ Salem high strain bandmill L.H. (R.H.) (s/n LL 0366-89) 9 spare saws

- Salem carriage drive DC (NO motor, gear box or controller)

- Operator Cab

- NO controls, No motor or controller drive, no guard, no pantograph.


 

Optional equipment

- Two (2) infeed log decks - 6 strand

- Two (2) infeed log hauls

- Outfeed rolls approx. 80’

 

 

 

 

 

return to top of page


Sharp Chain System 8’ – 10’

- Kockums/CanCar sharp chins system with holddown rolls

Drives

- CM&E model 18 6 knife canter with drives and linears

- Operator cab & controls (PC Direct Logic 205)

 

 

 

 

 

 


return to top of page

 

C-Frame small log breakdown system

- Conveyor Machinery C-frame carriage system w/cable drive

Pipe turner roll section

- CM&E Model 18 two (2) sided canter w/motors w/linear positioners

Six (6) knife heads

- Salem Two (2) saw box with motors and linears (39-1/2" & 48" dia. Saws)

- Outfeed separator table

- Operator cab and controls – manual sets (plc – Direct-Logic model 205)

- Hydraulics

 

                      

 

 

                                 

 

 

                          


return to top of page

 

8"x66" Schurman Combination Gang/Edger System including:

- Schurman 8"x66" Top Arbor combination gang

Splined arbor, 28" dia. Thin kerf saws, 4 shifting saws L.H. side,

10-12+ gang saws on R.H. side, 400HP arbor drive, linear positions,

HPU,

- Infeed table fed from both sides, with spotting chains and drive

- Outfeed table with drive

- Operator controls cab & controls (PLC – Direct Logic model 205)

 


return to top of page

 

Trimmer System

-Infeed transfer system with even ending rolls

-Infeed lug chains

-22’ Salem R.H. trimmer with line shaft drive (Schurman) (wheel lift – no cylinders)

-outfeed transfers

 

 


return to top of page

 

Chip Bins

-two (2) 20 unit chip bins complete with augar

-50’ waster conveyor feeding bins

-one (1) 30 unit chip bins

-50’ wasteconveyor feeding bin

 

 

 


return to top of page

 

Chippers

- 60" Sumner wastewood chipper HF/BD w/200HP motor


return to top of page

 

Chip Screen

-5’x8’ Rotex chip screen


return to top of page

 

Air Compressor

150HP Quincy Model 650H air compressor 3747hrs

return to top of page

 

 

 

 

 

 

 

          

                Used Equipment                 New Equipment               Contact              Services               About